Name: HVTECK CU 1/C 140TRXLPE CB PVC AIA PVC 8kV 133% CSA
Brand: Southwire
Rating: 5 (1 reviews)

Products > Industrial Products > HVTECK > SPEC26216

SPEC 26216

HVTECK CU 1/C 140TRXLPE CB PVC AIA PVC 8kV 133% CSA

Single Conductor, 140 Mils Tree Retardant Cross Linked Polyethylene, 133% Insulation Level, Concentric Bond, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

Download PDF

Construction:

Conductor:Class B compressed stranded bare copper per ASTM B3 and ASTM B8
Conductor Shield:Semi-conducting cross-linked copolymer
Insulation:140 Mils Tree Retardant Cross Linked Polyethylene 133% insulation level
Insulation Shield:Strippable semi-conducting cross-linked copolymer
Concentric Shield:Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
Neutral Separator:Mylar tape
Inner Jacket:PVC inner jacket
Armour:Aluminum Interlocked Armour (AIA)
Overall Jacket:Orange Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 8kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL). These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. Rated for 1000 lbs /FT maximum sidewall pressure. These cables feature sunlight and moisture resistance, exceptional corona resistance, resistance to most chemical soils and acids and are flame retardant.

Specifications:

ASTM B3 Soft or Annealed Copper Wire

ASTM B8 Concentric-Lay-Stranded Copper Conductors

CSA C22.2 No. 174 Cables in Hazardous Locations

CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods

CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV

CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV

CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating

CSA HL - for Hazardous Locations rating

CSA SUN RES - for Sunlight Resistant rating

ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable

ICEA T-29-520 Flame Test (210,000 BTU/Hr)

IEEE 383 Flame Test (70,000 btu)

IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)

FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)

AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV (Qualification Test Requirements)

Sample Print Legend:

(CSA) SOUTHWIRE (NESC) #P# 1/C [#AWG or #kcmil] CU 140 TRXLPE AIA 8kV 133% INS LEVEL CB [No. x SIZE] AWG SUN RES 105°C FT4 HL (-40°C) LTGG RoHS YEAR [SEQUENTIAL METER MARKS]

Table 1 – Weights and Measurements

Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Inner Jacket Thickness	Dia. Over Armour	Overall Jacket Thickness	Approx. OD	Approx. Weight
AWG/Kcmil	No.	inch	inch	mil	inch	No. x AWG	mil	inch	mil	inch	lb/1000ft
2	7	0.282	0.600	140	0.660	7 x 14	80	1.176	50	1.276	859
1	19	0.322	0.640	140	0.700	11 x 14	80	1.326	50	1.426	1007
1/0	19	0.361	0.679	140	0.739	11 x 14	80	1.365	50	1.465	1102
2/0	19	0.405	0.723	140	0.783	11 x 14	80	1.409	50	1.509	1219
3/0	19	0.456	0.774	140	0.834	13 x 14	80	1.460	50	1.560	1391
4/0	19	0.512	0.830	140	0.890	13 x 14	80	1.516	60	1.636	1600
250	37	0.558	0.884	140	0.944	17 x 14	80	1.570	60	1.690	1816
350	37	0.661	0.987	140	1.047	21 x 14	80	1.697	60	1.817	2291
500	37	0.789	1.115	140	1.175	26 x 14	80	1.825	60	1.945	2921
750	61	0.968	1.304	140	1.364	21 x 12	110	2.108	60	2.228	4171
1000	61	1.117	1.453	140	1.513	21 x 12	110	2.257	75	2.407	5147

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 2 – Electrical and Engineering Data

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity In Air 90°C	Allowable Ampacity Directly Buried 90°C
AWG/Kcmil	inch	lb	Ω/1000ft	Ω/1000ft	MΩ*1000ft	Ω/1000ft	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
2	8.9	530	0.162	0.204	0.051	0.056	0.186 + j0.031	0.192 + j0.039	5458	215	221
1	9.9	669	0.128	0.162	0.046	0.056	0.144 + j0.028	0.149 + j0.036	8577	245	247
1/0	10.2	844	0.102	0.128	0.042	0.054	0.11 + j0.027	0.115 + j0.035	8577	278	275
2/0	10.5	1064	0.081	0.102	0.039	0.052	0.084 + j0.025	0.089 + j0.033	8577	317	306
3/0	10.9	1342	0.064	0.081	0.036	0.050	0.063 + j0.024	0.069 + j0.032	10137	357	335
4/0	11.4	1692	0.051	0.065	0.032	0.048	0.047 + j0.022	0.053 + j0.03	10137	404	369
250	11.8	2000	0.043	0.056	0.031	0.047	0.038 + j0.021	0.044 + j0.029	13256	456	412
350	12.7	2800	0.031	0.041	0.027	0.045	0.023 + j0.02	0.029 + j0.028	16376	537	456
500	13.6	4000	0.022	0.030	0.023	0.042	0.012 + j0.018	0.018 + j0.026	20275	616	497
750	15.5	6000	0.014	0.023	0.020	0.041	0.005 + j0.017	0.011 + j0.025	26018	706	551
1000	16.8	8000	0.011	0.019	0.017	0.039	0.001 + j0.016	0.007 + j0.024	26018	813	596

* Inductive impedance is based on non-ferrous conduit with one diameter spacing.

Table 3 – Weights and Measurements (Metric)

Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Inner Jacket Thickness	Dia. Over Armour	Overall Jacket Thickness	Approx. OD	Approx. Weight
AWG/Kcmil	No.	mm	mm	mm	mm	No. x AWG	mm	mm	mm	mm	kg/km
2	7	7.16	15.24	3.56	16.76	7 x 14	2.03	29.87	1.27	32.41	1278
1	19	8.18	16.26	3.56	17.78	11 x 14	2.03	33.68	1.27	36.22	1499
1/0	19	9.17	17.25	3.56	18.77	11 x 14	2.03	34.67	1.27	37.21	1640
2/0	19	10.29	18.36	3.56	19.89	11 x 14	2.03	35.79	1.27	38.33	1814
3/0	19	11.58	19.66	3.56	21.18	13 x 14	2.03	37.08	1.27	39.62	2070
4/0	19	13.00	21.08	3.56	22.61	13 x 14	2.03	38.51	1.52	41.55	2381
250	37	14.17	22.45	3.56	23.98	17 x 14	2.03	39.88	1.52	42.93	2703
350	37	16.79	25.07	3.56	26.59	21 x 14	2.03	43.10	1.52	46.15	3409
500	37	20.04	28.32	3.56	29.85	26 x 14	2.03	46.36	1.52	49.40	4347
750	61	24.59	33.12	3.56	34.65	21 x 12	2.79	53.54	1.52	56.59	6207
1000	61	28.37	36.91	3.56	38.43	21 x 12	2.79	57.33	1.91	61.14	7660

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 4 – Electrical and Engineering Data (Metric)

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity In Air 90°C	Allowable Ampacity Directly Buried 90°C
AWG/Kcmil	mm	newton	Ω/km	Ω/km	MΩ*km	Ω/km	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
2	226.06	2359	0.5315	0.67	0.0155	0.1837	0.186 + j0.031	0.192 + j0.039	5458	215	221
1	251.46	2977	0.4199	0.53	0.0140	0.1837	0.144 + j0.028	0.149 + j0.036	8577	245	247
1/0	259.08	3756	0.3346	0.42	0.0128	0.1772	0.11 + j0.027	0.115 + j0.035	8577	278	275
2/0	266.70	4735	0.2657	0.33	0.0119	0.1706	0.084 + j0.025	0.089 + j0.033	8577	317	306
3/0	276.86	5972	0.2100	0.27	0.0110	0.1640	0.063 + j0.024	0.069 + j0.032	10137	357	335
4/0	289.56	7529	0.1673	0.21	0.0098	0.1575	0.047 + j0.022	0.053 + j0.03	10137	404	369
250	299.72	8900	0.1411	0.18	0.0094	0.1542	0.038 + j0.021	0.044 + j0.029	13256	456	412
350	322.58	12460	0.1017	0.13	0.0082	0.1476	0.023 + j0.02	0.029 + j0.028	16376	537	456
500	345.44	17800	0.0722	0.10	0.0070	0.1378	0.012 + j0.018	0.018 + j0.026	20275	616	497
750	393.70	26700	0.0459	0.08	0.0061	0.1345	0.005 + j0.017	0.011 + j0.025	26018	706	551
1000	426.72	35600	0.0361	0.06	0.0052	0.1280	0.001 + j0.016	0.007 + j0.024	26018	813	596

* Inductive impedance is based on non-ferrous conduit with one diameter spacing.

Revision: 1.000.000

Updated On: Aug. 18, 2023, 2:39 p.m. UTC