Products > Industrial > HVTECK > SPEC26152
...Canada
SPEC 26152

HVTECK CU 3/C 115TRXLPE TS PVC AIA PVC 5kV 133% or 8kV 100% CSA

3 Conductor, 115 Mils Tree Retardant Cross Linked Polyethylene, 5kV 133% or 8kV 100% Insulation Level, Tape Shield, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

...
Download PDF Download Excel Table
CableTech...

Construction:

  1. Conductor:Class B compressed stranded bare copper per ASTM B3 and ASTM B8
  2. Conductor Shield:Semi-conducting cross-linked copolymer
  3. Insulation:115 Mils Tree Retardant Cross Linked Polyethylene 133% insulation level
  4. Insulation Shield:Strippable semi-conducting cross-linked copolymer
  5. Copper Tape Shield:Helically wrapped 5 mil copper tape with 25% overlap
  6. Filler:Interstices filled with non-hydroscoping/non-wicking fillers
  7. Grounding Conductor:Class B compressed stranded bare copper ground per ASTM B3 and ASTM B8
  8. Binder:Polypropylene tape
  9. Inner Jacket:PVC inner jacket
  10. Armour:Aluminum Interlocked Armour (AIA)
  11. Overall Jacket:Orange Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 5kV / 8kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL). These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. For installation in cable trays, duct banks, direct burial, troughs, continuous rigid cable supports and concrete encaseable. Rated for 1000 lbs /FT maximum sidewall pressure. These cables feature sunlight and moisture resistance, exceptional corona resistance, resistance to most chemical soils and acids and are flame retardant.

Specifications:

  • ASTM B3 Soft or Annealed Copper Wire
  • ASTM B8 Concentric-Lay-Stranded Copper Conductors
  • CSA C22.2 No. 174 Cables in Hazardous Locations
  • CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods
  • CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV
  • CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV
  • CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating
  • CSA HL - for Hazardous Locations rating
  • CSA SUN RES - for Sunlight Resistant rating
  • ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable
  • ICEA T-29-520 Flame Test (210,000 BTU/Hr)
  • IEEE 383 Flame Test (70,000 btu)
  • IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test
  • FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)
  • AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV (Qualification Test Requirements)

    • Sample Print Legend:

    {SQMTR} {CSA} SOUTHWIRE® POWER CABLE {NESC} 3/C XXX KCMIL CU X.XXmm (115 mils) TR-XLPE AIA GW 1 X X AWG CU 5KV 133%/8KV 100% INS LEVEL 25%TS SUN. RES. 105°C FT4 HL (-40°C) LTGG RoHS
    Table 1 – Weights and Measurements
    Stock NumberCond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldGroundGround SizeInner Jacket ThicknessDia. Over Inner JacketDia. Over ArmourOverall Jacket ThicknessApprox. ODCopper WeightApprox. WeightConduit Size*
    AWG/KcmilNo.inchinchmilinchNo. x AWGAWGmilinchinchmilinchlb/1000ftlb/1000ftinch
    672897270.2830.5511150.6111x66801.5061.874601.99488722422.5
    6719751190.3220.591150.651x66801.591.958602.078104823672.5
    6729051/0190.3620.631150.691x661101.7362.104602.224126829083
    6729472/0190.4050.6741150.7341x661101.8312.199602.319152931463
    TBA3/0190.4560.7241150.7841x441101.9392.249602.369189530953
    5990014/0190.5120.781150.841x441102.062.428752.578233542623.5
    671984250370.5580.8341150.8941x441102.1772.545752.695269347323.5
    640917350370.6610.9171150.9771x331102.3562.724752.874369559833.5
    599006500370.7891.0421151.1021x331102.6262.994753.144512877254
    674110^500370.7891.0421151.1021x331102.6262.994753.144512877294
    671381750610.9681.2541151.3141x221253.1143.502853.6727559109555
    TBA1000611.1171.4031151.4631x111253.4363.746853.9169980124825
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination
    ^ Stock Code: 674110. Yellow Jacket
    TBA stock codes are estimations only and actual product may vary. Please wait until a stock code is assigned to purchase connectors and/or fittings.
    Table 2 – Electrical and Engineering Data
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence ImpedancePositive Sequence ImpedancePhase Short Circuit Current @ 6 CyclesAllowable Ampacity In Air 90°CAllowable Ampacity Directly Buried 90°C
    AWG/KcmilinchlbΩ/1000ftΩ/1000ftMΩ*1000ftΩ/1000ftΩ/1000ftΩ/1000ftAmpAmpAmp
    21415920.1620.2210.0370.0240.577+j0.5560.221+j0.0411924172201
    114.520080.1280.1750.0340.0220.536+j0.5340.175+j0.0392045197228
    1/015.625340.1020.1390.0310.0210.503+j0.5130.139+j0.0372169225257
    2/016.231940.0820.1120.0290.020.479+j0.4920.112+j0.0362305260292
    3/016.640270.0640.0870.0260.0190.457+j0.4680.087+j0.0352460297330
    4/01850780.0510.070.0240.0170.441+j0.4430.070+j0.0342634342372
    25018.960000.0430.0590.0220.0170.430+j0.4210.059+j0.0332801376410
    35020.184000.0310.0430.0180.0150.412+j0.3890.043+j0.0313058460487
    50022120000.0210.030.0150.0140.394+j0.3470.030+j0.0303445556573
    50022120000.0210.030.0150.0140.394+j0.3470.030+j0.0303445556573
    75025.7180000.0140.0210.0140.0130.370+j0.2880.021+j0.0294102678668
    100027.4240000.0110.0180.0120.0120.355+j0.2550.018+j0.0284564798772
    * Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
    * Calculations are based on 5 mil 25 % over lapping copper tape shield / Conductor temperature of 90°C / Shield temperature of 45°C / Earth resistivity of 100 ohms-meter
    * Ampacities are based on Table D17N of the Canadian Electrical Code Part I (40°C Ambient Air Temperature, indoor installation)
    * Ampacities are based on Table D17E of the Canadian Electrical Code Part I
    * CEC ampacities are based on:
    3/C in air copper and aluminum: D17N
    3/C direct buried copper and aluminum: D17E
    Table 3 – Weights and Measurements (Metric)
    Stock NumberCond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldGroundGround SizeInner Jacket ThicknessDia. Over Inner JacketDia. Over ArmourOverall Jacket ThicknessApprox. ODCopper WeightApprox. WeightConduit Size*
    AWG/KcmilNo.mmmmmmmmNo. x AWGAWGmmmmmmmmmmkg/kmkg/kminch
    672897277.1914.002.9215.521x662.0338.2547.601.5250.65132033362.5
    6719751198.1814.992.9216.511x662.0340.3949.731.5252.78156035222.5
    6729051/0199.1916.002.9217.531x662.7944.0953.441.5256.49188743283
    6729472/01910.2917.122.9218.641x662.7946.5155.851.5258.90227546823
    TBA3/01911.5818.392.9219.911x442.7949.2557.121.5260.17282046063
    5990014/01913.0019.812.9221.341x442.7952.3261.671.9165.48347563433.5
    6719842503714.1721.182.9222.711x442.7955.3064.641.9168.45400870423.5
    6409173503716.7923.292.9224.821x332.7959.8469.191.9173.00549989043.5
    5990065003720.0426.472.9227.991x332.7966.7076.051.9179.867631114964
    674110^5003720.0426.472.9227.991x332.7966.7076.051.9179.867631115024
    6713817506124.5931.852.9233.381x223.1879.1088.952.1693.2711249163035
    TBA10006128.3735.642.9237.161x113.1887.2795.152.1699.4714852185755
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination
    ^ Stock Code: 674110. Yellow Jacket
    TBA stock codes are estimations only and actual product may vary. Please wait until a stock code is assigned to purchase connectors and/or fittings.
    Table 4 – Electrical and Engineering Data (Metric)
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence ImpedancePositive Sequence ImpedancePhase Short Circuit Current @ 6 CyclesAllowable Ampacity In Air 90°CAllowable Ampacity Directly Buried 90°C
    AWG/KcmilmmnewtonΩ/kmΩ/kmMΩ*kmΩ/kmΩ/1000ftΩ/1000ftAmpAmpAmp
    2355.6070840.53150.730.01130.07870.577+j0.5560.221+j0.0411924172201
    1368.3089360.41990.570.01040.07220.536+j0.5340.175+j0.0392045197228
    1/0396.24112760.33460.460.00940.06890.503+j0.5130.139+j0.0372169225257
    2/0411.48142130.26900.370.00880.06560.479+j0.4920.112+j0.0362305260292
    3/0421.64179200.21000.290.00790.06230.457+j0.4680.087+j0.0352460297330
    4/0457.20225970.16730.230.00730.05580.441+j0.4430.070+j0.0342634342372
    250480.06267000.14110.190.00670.05580.430+j0.4210.059+j0.0332801376410
    350510.54373800.10170.140.00550.04920.412+j0.3890.043+j0.0313058460487
    500558.80534000.06890.100.00460.04590.394+j0.3470.030+j0.0303445556573
    500558.80534000.06890.100.00460.04590.394+j0.3470.030+j0.0303445556573
    750652.78801000.04590.070.00430.04270.370+j0.2880.021+j0.0294102678668
    1000695.961068000.03610.060.00370.03940.355+j0.2550.018+j0.0284564798772
    * Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
    * Calculations are based on 5 mil 25 % over lapping copper tape shield / Conductor temperature of 90°C / Shield temperature of 45°C / Earth resistivity of 100 ohms-meter
    * Ampacities are based on Table D17N of the Canadian Electrical Code Part I (40°C Ambient Air Temperature, indoor installation)
    * Ampacities are based on Table D17E of the Canadian Electrical Code Part I
    * CEC ampacities are based on:
    3/C in air copper and aluminum: D17N
    3/C direct buried copper and aluminum: D17E

    Revision: 1.000.003

    Updated On: Dec. 31, 2024, 11:07 p.m. UTC