SPEC 26226

HVTECK AL 1/C 140NLEPR CB PVC AIA PVC 8kV 133% CSA

Single Conductor, 140 Mils No Lead Ethylene Propylene Rubber (NL-EPR), 133% Insulation Level, Concentric Bond, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

...

Construction:

  1. Conductor:Class B compact stranded 8000 Series aluminum per ASTM B800 and ASTM B836
  2. Conductor Shield:Semi-conducting cross-linked copolymer; A conductor separator is used for cable size larger than or equal to 500 Kcmil
  3. Insulation:140 Mils No Lead Ethylene Propylene Rubber (NL-EPR) 133% insulation level
  4. Insulation Shield:Strippable semi-conducting cross-linked copolymer
  5. Concentric Shield:Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
  6. Neutral Separator:Mylar tape
  7. Inner Jacket:PVC inner jacket
  8. Armour:Aluminum Interlocked Armour (AIA)
  9. Overall Jacket:Orange Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 8kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL). These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. Rated for 1000 lbs /FT maximum sidewall pressure. These cables feature sunlight and moisture resistance, exceptional corona resistance, resistance to most chemical soils and acids and are flame retardant.

Specifications:

  • ASTM B801 Concentric-Lay-Stranded Conductors of 8000 Series Aluminum Alloy
  • ASTM B836 Compact Rounded Stranded Aluminum Conductors
  • CSA C22.2 No. 174 Cables in Hazardous Locations
  • CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods
  • CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV
  • CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV
  • CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating
  • CSA HL - for Hazardous Locations rating
  • CSA SUN RES - for Sunlight Resistant rating
  • ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable
  • ICEA T-29-520 Flame Test (210,000 BTU/Hr)
  • IEEE 383 Flame Test (70,000 btu)
  • IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)
  • FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)
  • AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV (Qualification Test Requirements)
  • Sample Print Legend:

    (CSA) SOUTHWIRE (NESC) #P# 1/C [#AWG or #kcmil] CPT AL 140 NLEPR AIA 8kV 133% INS LEVEL CB [No. x SIZE] AWG SUN RES 105°C FT4 HL (-40°C) LTGG RoHS YEAR [SEQUENTIAL METER MARKS]
    Table 1 – Weights and Measurements
    Cond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldConcentric NeutralInner Jacket ThicknessDia. Over ArmourOverall Jacket ThicknessApprox. ODApprox. Weight
    AWG/KcmilNo.inchinchmilinchNo. x AWGmilinchmilinchlb/1000ft
    270.2680.5861400.6467x14801.156501.256706
    1190.2980.6161400.6767x14801.186501.286743
    1/0190.3360.6541400.7147x14801.334501.434804
    2/0190.3760.6941400.75411x14801.374501.474913
    3/0190.4220.7401400.80011x14801.420501.520978
    4/0190.4740.7921400.85211x14801.472501.5721058
    250370.5200.8461400.90613x14801.526601.6461195
    350370.6150.9411401.00117x14801.679601.7991464
    500370.7351.0611401.12121x14801.799601.9191753
    750610.9081.2441401.30417x12801.982602.1022305
    1000611.0601.3961401.45617x121102.194602.3142794
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    * Strand count meets minimum number per ASTM
    Table 2 – Electrical and Engineering Data
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence ImpedancePositive Sequence ImpedancePhase Short Circuit Current @ 6 CyclesAllowable Ampacity In Air 90°CAllowable Ampacity Directly Buried 90°C
    AWG/KcmilinchlbΩ/1000ftΩ/1000ftMΩ*1000ftΩ/1000ftΩ/1000ftΩ/1000ftAmpAmpAmp
    215.13980.2670.3360.0370.0570.690 + j0.4940.337 + j0.0575458169176
    115.45020.2110.2660.0340.0550.622 + j0.4760.267 + j0.0545458194198
    1/017.26330.1680.2110.0310.0550.567 + j0.4570.212 + j0.0545458222223
    2/017.77980.1330.1670.0290.0530.525 + j0.4370.168 + j0.0528577255250
    3/018.210060.1050.1330.0260.0510.492 + j0.4160.134 + j0.0508577290278
    4/018.912690.0840.1050.0240.0490.464 + j0.3940.106 + j0.0488577329309
    25019.815000.0710.0900.0230.0480.447 + j0.3730.091 + j0.04710137370347
    35021.621000.0500.0650.0200.0460.417 + j0.3390.066 + j0.04513256446402
    50023.030000.0350.0460.0170.0440.391 + j0.3010.047 + j0.04216376533451
    75025.245000.0240.0330.0140.0410.363 + j0.2540.034 + j0.03921062631500
    100027.860000.0180.0260.0130.0400.342 + j0.2220.027 + j0.03821062707539
    * Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
    * CEC ampacities are based on:
    3-1/C in air copper and aluminum: D17M
    3-1/C direct buried copper and aluminum: D17A
    Table 3 – Weights and Measurements (Metric)
    Cond. SizeStrandDiameter Over ConductorDiameter Over InsulationInsul. ThicknessDiameter Over Insulation ShieldConcentric NeutralInner Jacket ThicknessDia. Over ArmourOverall Jacket ThicknessApprox. ODApprox. Weight
    AWG/KcmilNo.mmmmmmmmNo. x AWGmmmmmmmmkg/km
    276.8114.883.5616.417x142.0329.361.2731.901051
    1197.5715.653.5617.177x142.0330.121.2732.661106
    1/0198.5316.613.5618.147x142.0333.881.2736.421196
    2/0199.5517.633.5619.1511x142.0334.901.2737.441359
    3/01910.7218.803.5620.3211x142.0336.071.2738.611455
    4/01912.0420.123.5621.6411x142.0337.391.2739.931574
    2503713.2121.493.5623.0113x142.0338.761.5241.811778
    3503715.6223.903.5625.4317x142.0342.651.5245.692179
    5003718.6726.953.5628.4721x142.0345.691.5248.742609
    7506123.0631.603.5633.1217x122.0350.341.5253.393430
    10006126.9235.463.5636.9817x122.7955.731.5258.784158
    All dimensions are nominal and subject to normal manufacturing tolerances
    ◊ Cable marked with this symbol is a standard stock item
    * Strand count meets minimum number per ASTM
    Table 4 – Electrical and Engineering Data (Metric)
    Cond. SizeMin Bending RadiusMax Pull TensionDC Resistance @ 25°CAC Resistance @ 90°CCapacitive Reactance @ 60HzInductive Reactance @ 60HzZero Sequence ImpedancePositive Sequence ImpedancePhase Short Circuit Current @ 6 CyclesAllowable Ampacity In Air 90°CAllowable Ampacity Directly Buried 90°C
    AWG/KcmilmmnewtonΩ/kmΩ/kmMΩ*kmΩ/kmΩ/1000ftΩ/1000ftAmpAmpAmp
    2383.5417710.87601.100.01130.18700.690 + j0.4940.337 + j0.0575458169176
    1391.1622340.69230.870.01040.18040.622 + j0.4760.267 + j0.0545458194198
    1/0436.8828170.55120.690.00940.18040.567 + j0.4570.212 + j0.0545458222223
    2/0449.5835510.43640.550.00880.17390.525 + j0.4370.168 + j0.0528577255250
    3/0462.2844770.34450.440.00790.16730.492 + j0.4160.134 + j0.0508577290278
    4/0480.0656470.27560.340.00730.16080.464 + j0.3940.106 + j0.0488577329309
    250502.9266750.23290.300.00700.15750.447 + j0.3730.091 + j0.04710137370347
    350548.6493450.16400.210.00610.15090.417 + j0.3390.066 + j0.04513256446402
    500584.20133500.11480.150.00520.14440.391 + j0.3010.047 + j0.04216376533451
    750640.08200250.07870.110.00430.13450.363 + j0.2540.034 + j0.03921062631500
    1000706.12267000.05910.090.00400.13120.342 + j0.2220.027 + j0.03821062707539
    * Inductive impedance is based on non-ferrous conduit with one diameter spacing center-to-center.
    * CEC ampacities are based on:
    3-1/C in air copper and aluminum: D17M
    3-1/C direct buried copper and aluminum: D17A

    Revision: 1.000.000

    Updated On: July 12, 2024, 5:43 p.m. UTC