Name: HVTECK CU 1/C 220NLEPR CB PVC AIA PVC 15kV 133% CSA
Brand: Southwire
Rating: 5 (1 reviews)

Products > Industrial Products > HVTECK > SPEC26306

SPEC 26306

HVTECK CU 1/C 220NLEPR CB PVC AIA PVC 15kV 133% CSA

Single Conductor, 220 Mils No Lead Ethylene Propylene Rubber (NL-EPR), 133% Insulation Level, Concentric Bond, Polyvinyl Chloride (PVC) Inner Jacket, Aluminum Interlocked Armour (AIA), Polyvinyl Chloride (PVC) Jacket

Download PDF

Construction:

Conductor:Class B compressed stranded bare copper per ASTM B3 and ASTM B8
Conductor Shield:Semi-conducting cross-linked copolymer
Insulation:220 Mils No Lead Ethylene Propylene Rubber (NL-EPR) 133% insulation level
Insulation Shield:Strippable semi-conducting cross-linked copolymer
Concentric Shield:Concentrically applied copper bond / shield wires. Complies with greater than the minimum requirement as per Table 44, CSA Standard C68.10 and Table 16A, Canadian Electrical Code Part 1
Neutral Separator:Mylar tape
Inner Jacket:PVC inner jacket
Armour:Aluminum Interlocked Armour (AIA)
Overall Jacket:Red Polyvinyl Chloride (PVC) Jacket

Applications and Features:

Southwire's 15kV HVTECK is a CSA armoured cable for industrial and commercial medium voltage applications. Rated FT4, -40°C, Hazardous Locations (HL). These cables are capable of operating continuously at the conductor temperature not in excess of 105°C for normal operation, 140°C for emergency overload, and 250°C for short circuit conditions. Rated for 1000 lbs /FT maximum sidewall pressure. These cables feature sunlight and moisture resistance, exceptional corona resistance, resistance to most chemical soils and acids and are flame retardant.

Specifications:

ASTM B3 Soft or Annealed Copper Wire

ASTM B8 Concentric-Lay-Stranded Copper Conductors

CSA C22.2 No. 174 Cables in Hazardous Locations

CSA C22.2 No. 2556 & No. 0.3 Wire and Cable Test Methods

CSA C68.10 Shielded Power Cables for Commercial and Industrial Applications - 5 to 46 KV

CSA C68.3 Shielded & Concentric Neutral Power Cable - 5 to 46 kV

CSA LTGG [-40°C] - as per C68.10 - for Cold Bend and Impact rating

CSA HL - for Hazardous Locations rating

CSA SUN RES - for Sunlight Resistant rating

ICEA S-93-639 (NEMA WC 74) 5-46 KV Shielded Power Cable

ICEA T-29-520 Flame Test (210,000 BTU/Hr)

IEEE 383 Flame Test (70,000 btu)

IEEE 1202 FT4 Flame Test (70,000) BTU/hr Vertical Tray Test (1/0 and Larger)

FT1 Flame Test (1,706 BTU/Hr nominal - Vertical Wire Flame Test)

AEIC CS-8 Specification for extruded dielectric shielded power cables rated for 5 through 46KV

Sample Print Legend:

(CSA) SOUTHWIRE (NESC) #P# 1/C [#AWG or #kcmil] CU 220 NLEPR AIA 15kV 133% INS LEVEL CB [No. x SIZE] AWG SUN RES 105°C FT4 HL (-40°C) LTGG RoHS YEAR [SEQUENTIAL METER MARKS]

Table 1 – Weights and Measurements

Stock Number	Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Inner Jacket Thickness	Dia. Over Armour	Overall Jacket Thickness	Approx. OD	Approx. Weight
	AWG/Kcmil	No.	inch	inch	mil	inch	No. x AWG	mil	inch	mil	inch	lb/1000ft
TBA	2	7	0.282	0.760	220	0.820	7 x 14	80	1.446	50	1.546	1033
TBA	1	19	0.322	0.800	220	0.860	11 x 14	80	1.486	50	1.586	1176
TBA	1/0	19	0.361	0.839	220	0.899	11 x 14	80	1.525	60	1.645	1308
646911	2/0	19	0.405	0.884	220	0.944	17 x 16	80	1.424	50	1.524	1398
TBA	3/0	19	0.456	0.934	220	0.994	13 x 14	80	1.620	60	1.740	1613
TBA	4/0	19	0.512	0.990	220	1.050	13 x 14	80	1.700	60	1.820	1831
TBA	250	37	0.558	1.044	220	1.104	17 x 14	80	1.754	60	1.874	2054
TBA	350	37	0.661	1.147	220	1.207	21 x 14	80	1.857	60	1.977	2602
646932	500	37	0.789	1.252	220	1.312	27 X 14	80	1.950	60	2.070	3214
TBA	750	61	0.968	1.464	220	1.524	21 x 12	110	2.268	75	2.418	4524
587685	750	61	0.968	1.464	220	1.524	21 X 12	110	2.276	75	2.426	4617
TBA	1000	61	1.117	1.613	220	1.673	21 x 12	110	2.417	75	2.567	5454

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 2 – Electrical and Engineering Data

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity In Air 90°C	Allowable Ampacity Directly Buried 90°C
AWG/Kcmil	inch	lb	Ω/1000ft	Ω/1000ft	MΩ/1000ft	Ω/1000ft	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
2	10.8	530	0.162	0.204	0.051	0.061	0.186 + j0.035	0.192 + j0.043	5458	215	221
1	11.1	669	0.128	0.162	0.047	0.058	0.144 + j0.032	0.15 + j0.04	8577	245	247
1/0	11.5	844	0.102	0.128	0.043	0.057	0.11 + j0.031	0.116 + j0.039	8577	278	275
2/0	10.6	1064	0.081	0.102	0.040	0.055	0.084 + j0.029	0.09 + j0.037	8577	317	306
3/0	12.1	1342	0.064	0.081	0.037	0.052	0.063 + j0.027	0.069 + j0.035	10137	357	335
4/0	12.7	1692	0.051	0.065	0.034	0.051	0.047 + j0.026	0.053 + j0.034	10137	404	369
250	13.1	2000	0.043	0.056	0.032	0.050	0.038 + j0.025	0.044 + j0.033	13256	456	412
350	13.8	2800	0.031	0.041	0.028	0.047	0.023 + j0.023	0.029 + j0.031	16376	537	456
500	14.4	4000	0.022	0.030	0.025	0.044	0.012 + j0.021	0.018 + j0.029	20275	616	497
750	16.9	6000	0.014	0.023	0.021	0.043	0.005 + j0.019	0.011 + j0.027	26018	706	551
750	16.9	6000	0.014	0.023	0.021	0.043	0.005 + j0.019	0.011 + j0.027	26018	706	551
1000	17.9	8000	0.011	0.019	0.019	0.041	0.001 + j0.018	0.008 + j0.026	26018	813	596

* Inductive impedance is based on non-ferrous conduit with one diameter spacing.

Table 3 – Weights and Measurements (Metric)

Stock Number	Cond. Size	Strand	Diameter Over Conductor	Diameter Over Insulation	Insul. Thickness	Diameter Over Insulation Shield	Concentric Neutral	Inner Jacket Thickness	Dia. Over Armour	Overall Jacket Thickness	Approx. OD	Approx. Weight
	AWG/Kcmil	No.	mm	mm	mm	mm	No. x AWG	mm	mm	mm	mm	kg/km
TBA	2	7	7.16	19.30	5.59	20.83	7 x 14	2.03	36.73	1.27	39.27	1537
TBA	1	19	8.18	20.32	5.59	21.84	11 x 14	2.03	37.74	1.27	40.28	1750
TBA	1/0	19	9.17	21.31	5.59	22.83	11 x 14	2.03	38.73	1.52	41.78	1947
646911	2/0	19	10.29	22.45	5.59	23.98	17 x 16	2.03	36.17	1.27	38.71	2080
TBA	3/0	19	11.58	23.72	5.59	25.25	13 x 14	2.03	41.15	1.52	44.20	2400
TBA	4/0	19	13.00	25.15	5.59	26.67	13 x 14	2.03	43.18	1.52	46.23	2725
TBA	250	37	14.17	26.52	5.59	28.04	17 x 14	2.03	44.55	1.52	47.60	3057
TBA	350	37	16.79	29.13	5.59	30.66	21 x 14	2.03	47.17	1.52	50.22	3872
646932	500	37	20.04	31.80	5.59	33.32	27 X 14	2.03	49.53	1.52	52.58	4783
TBA	750	61	24.59	37.19	5.59	38.71	21 x 12	2.79	57.61	1.91	61.42	6732
587685	750	61	24.59	37.19	5.59	38.71	21 X 12	2.79	57.81	1.91	61.62	6871
TBA	1000	61	28.37	40.97	5.59	42.49	21 x 12	2.79	61.39	1.91	65.20	8116

All dimensions are nominal and subject to normal manufacturing tolerances

◊ Cable marked with this symbol is a standard stock item

1 Comply with ICEA S-93-639 Appendix C for jacket thickness determination

Table 4 – Electrical and Engineering Data (Metric)

Cond. Size	Min Bending Radius	Max Pull Tension	DC Resistance @ 25°C	AC Resistance @ 90°C	Capacitive Reactance @ 60Hz	Inductive Reactance @ 60Hz	Zero Sequence Impedance*	Positive Sequence Impedance*	Phase Short Circuit Current @ 60Hz	Allowable Ampacity In Air 90°C	Allowable Ampacity Directly Buried 90°C
AWG/Kcmil	mm	newton	Ω/km	Ω/km	MΩ/km	Ω/km	Ω/1000ft	Ω/1000ft	kAmp	Amp	Amp
2	274.32	2359	0.5315	0.67	0.0155	0.2001	0.186 + j0.035	0.192 + j0.043	5458	215	221
1	281.94	2977	0.4199	0.53	0.0143	0.1903	0.144 + j0.032	0.15 + j0.04	8577	245	247
1/0	292.10	3756	0.3346	0.42	0.0131	0.1870	0.11 + j0.031	0.116 + j0.039	8577	278	275
2/0	269.24	4735	0.2657	0.33	0.0122	0.1804	0.084 + j0.029	0.09 + j0.037	8577	317	306
3/0	307.34	5972	0.2100	0.27	0.0113	0.1706	0.063 + j0.027	0.069 + j0.035	10137	357	335
4/0	322.58	7529	0.1673	0.21	0.0104	0.1673	0.047 + j0.026	0.053 + j0.034	10137	404	369
250	332.74	8900	0.1411	0.18	0.0098	0.1640	0.038 + j0.025	0.044 + j0.033	13256	456	412
350	350.52	12460	0.1017	0.13	0.0085	0.1542	0.023 + j0.023	0.029 + j0.031	16376	537	456
500	365.76	17800	0.0722	0.10	0.0076	0.1444	0.012 + j0.021	0.018 + j0.029	20275	616	497
750	429.26	26700	0.0459	0.08	0.0064	0.1411	0.005 + j0.019	0.011 + j0.027	26018	706	551
750	429.26	26700	0.0459	0.08	0.0064	0.1411	0.005 + j0.019	0.011 + j0.027	26018	706	551
1000	454.66	35600	0.0361	0.06	0.0058	0.1345	0.001 + j0.018	0.008 + j0.026	26018	813	596

* Inductive impedance is based on non-ferrous conduit with one diameter spacing.

Revision: 1.000.000

Updated On: Aug. 18, 2023, 2:39 p.m. UTC